00.38
Manusia Biasa
ESteps of mounting Fan
(Langkah-Langkah Pemasangan Fan)
Mount the inferior part of the inlet
box with the inferior part of the casing. Use ceramics cords for sealing. Place
the inferior part of the fan on the concrete. Let +/- 50 mm below for the final
concrete. Mount the anchor bolts and adjust the inferior part of the fan with
the adjusting screws. The fan must be fixed on the foundations by means of
sheet of fitting on each side of anchoring and must be tightened when all is of
level and with good height.
Place the bearing support on the
concrete. Let +/- 50 mm below for the final concrete. Mount he anchor bolts and
adjust the support with the adjusting screws. These supports must be fixed on
the foundations by means of sheet of fitting on each side of anchoring and must
be tightened when all is of level and with good height.
Mount the rotor with inlet cones and
fix the bearings on their supports. Fix the free bearing with all the axial gap
behind the roller. The gap at the shaft pass must be the same all around. Fix
the inlet cone with the inferior part of the fan (see detail B – Sheet 6). Turn
the rotor by hand to see if any friction. Readjust if necessary
.
Mount the motor frame on the concrete.
Let +/- 50 mm below for the final concrete. Mount the anchor bolts and adjust
the frame with the adjusting screws. The frame must be fixed on the foundations
by means of sheet of fitting on each side of anchoring and must be tightened
when all is of level and with good height.
Mount the suprerior part of the
casing. Use ceramic cords for sealing. Fix completely the 2 inlet cone with the
superior part of the fan.
Mount the upper part of the inlet box.
Use ceramic cords for sealing. Check all axes. Strictly tighten the nuts on the
anchor bolts
Mount the stiffeners pipe in the inlet box.
Mount the shaft sealing and the
cooling disc. Make the final concrete (use non-shrink concrete) and fill the
anchor holes. After the drying up period (24 to 48 hours) fasten the bolts
correctly. Mount the motor on the support with a gap of the 2 half coupling of
9 mm. Do the alignment of coupling (check motor shaft and fan shaft). Refer you
to the coupling documentation.
Mount the damper. Use ceramic cords
for sealing. Mount the regulation for the damper. Adjust the support for the
actuator on the concrete and fix it. Fix the actuator on his support. And
connect it with the damper. Adjust the OPEN/CLOSE on the actuator.
Mount on each bearing a PT100 and a
VS068 (not CBV supply). Fill the bearings with oil (5,2 litre).
Mount the coupling guard, the shaft
guard and the cooling disc guard.
Open the drain of the casing, let get
out the water and after, close the drain.
Mount the security accessories.
Connect
the motor and check the rotating direction.
Procedure of maintenance
- Clear regularly the inlet parts of
the fan,
- Never let foreign matter in the
casing,
- Remove traces and dust on the
impeller; they are cause of dangerous balancing,
- Check the quality of the welding,
- Check regularly the fixation and the
tightening of bolts,
- Check the lubrication of the
bearings,
- Check the correct position of the
shaft seal,
- Check the adequate working of the
control equipments,
- Make sure that the impeller doesn’t
rub against the shaped inlet,
- Check the coupling (wear of elastic
parts),
- Check the alignment of motor and fan
axis,
- Check the lubrication of the motor,
-
Installed all the protection guards.
Lubrication
The bearings lubricated by oil are
equipped on each side with lubrication holes. Those are not used to lubricate
of the rollers but to fill the seal room. This grease is used to prevent
impurities entering the bearing and to prevent oil to get out of the bearing. A
little quantity of grease is necessary to fit this function. The grease to use is
mineral type ALVANIA RL2 (or equivalent). This grease has to be replaced with
the changing of the lubrication oil during the fan working.
The changes of oil are to be read in
the following table:
Possible
troubles and remedies
Characteristic
Flow / pressure and Flow / power
